Comparison ledger
Applied Materials 0020 81665 Part, Neslab CFT 75 Chiller, side by side. Every value shown is drawn from the cited encyclopedia entries.
| Attribute | 0020 81665 PartApplied Materials | CFT 75 ChillerNeslab |
|---|---|---|
| OEM | Applied Materials | Neslab |
| Category | Lab & Support Equipment | Lab & Support Equipment |
| Wafer size | — | — |
| Process node | — | — |
| Introduced | — | — |
| Production run | — | — |
| Lifecycle | — | — |
| Lifecycle milestones | — | 2009 service-business acquisition |
| Control system | — | — |
| Generation | — | — |
| Family | Applied Materials 0020 81665 Part | Neslab CFT 75 Chiller |
| Cited variants | — |
|
| Specifications | ||
| Configuration | Guide, Fiber Mount, Ude, Lk[2] | — |
| Make | — | Neslab[3] |
| Model | — | CFT 75[3] |
| Type | — | Recirculating chiller[1] |
| Refrigeration system | — | Air-cooled[1] |
| Phase | — | Single phase[4] |
| Temperature range | — | 5C to 35C[4] |
| Flow rate at 20ºC / 30 PSI (PD2 Pump) | — | 3.8 GPM[4] |
| Cooling capacity at 20C | — | 2100 Watts[4] |
| Available voltage | — | 200-230V 1 Ph[4] |
| Plumbing connections | — | 1/2 inch NPT[1] |
| Cooling fluid | — | Tap water is the recommended fluid for operation.[1] |
| Cooling system | — | Air-cooled refrigeration system[1] |
| Cooling capacity | — | 2100 watts at 20°C[4] |
| Power requirements | — | 208/230V, 60Hz[1] |
| Reservoir volume | — | 6.8 liters (1.8 gallons)[1] |
| Refrigerant | — | R134a[1] |
| Flow rate at 20°C / 30 PSI (PD1 Pump) | — | 0.9 GPM[4] |
| Air intake required | — | 800 cubic feet per minute[1] |
| Temperature stability | — | ±0.5°[1] |
| Dimensions (H x W x D) | — | 67.3 x 37.8 x 65.4 cm (26½ x 147/8 x 25¾ inches)[1] |
| Pump capacity | — | 60 PSI / 30 Bar; flow 2.0 LPM (5 PSI) to 20 LPM (15-20 PSI) approx.[1] |
| Flow Rate at 20ºC / 30 PSI (PD1 Pump) | — | .9 GPM[4] |
| Cooling options | — | Air only[4] |
| Condenser | — | Air-cooled; air drawn in the front and discharged through rear and side[1] |
| Compliance | — | CE label; LVD 73/23/EEC; UL 3101-1:93; EMC 89/336/EEC EN 55011 Class A[1] |
| Fluid viscosity requirement | — | 50 centistokes or less at lowest operating temperature[1] |
| Full rated capacity ambient temperature | — | Up to approximately +38°C[1] |
| Air intake requirement | — | Approximately 800 cubic feet per minute for full rated capacity[1] |
| OEM | — | Neslab[3] |
| Cooling configuration | — | Air only[4] |
| Unit dimensions (H x W x D) | — | 67.3 x 37.8 x 65.4 cm[1] |
| Cooling fluid recommendation | — | Tap water[1] |
| Cooling type | — | Air cooled[1] |
| Cooling capacity at 20°C | — | 2100 W[4] |
Plan your fab
Building a Lab & Support Equipment process? Get a complete equipment list.
Open the fab equipment planner →