Zeiss
O Inspect 322 CMM
The Zeiss O Inspect 322 is a coordinate measuring machine. The Zeiss O Inspect 322 has a measuring volume of 300 mm in X, 200 mm in Y, and 200 mm in Z. The Zeiss O Inspect 322 uses multisensor measurement technology including optical and tactile passive sensors.[1]
Plate 01Zeiss O Inspect 322 CMM Demo
DDTestVideosWatch on YouTube
What it is
General reference — not yet source-verifiedA coordinate measuring machine is a metrology system used to determine the geometry of a part by measuring positions on its surfaces and features. Coordinate measuring machines are used in inspection and dimensional verification workflows where measured results are compared with design intent or process targets.
How it works
General reference — not yet source-verifiedA coordinate measuring machine operates by moving a sensor system through a defined measurement space and recording coordinates from contacted points or optically observed features. Optical sensing supports noncontact measurement of visible edges and surfaces, while tactile sensing supports direct probing of physical features. Integrated control software typically manages motion, sensor behavior, scan routines, alignment, and reporting.
Where it fits in the process flow
General reference — not yet source-verifiedCoordinate measuring machines are used after fabrication or machining steps when dimensional confirmation is required before release to the next operation. Coordinate measuring machines are commonly placed in quality control, incoming inspection, in process verification, and final inspection flows rather than in the primary material removal or deposition step itself.
Applications
General reference — not yet source-verifiedCoordinate measuring machines are used to inspect part dimensions, feature locations, profiles, and form on precision components. Multisensor coordinate measuring machines are suited to workflows that combine optical feature capture with tactile probing so that different feature types on the same workpiece can be measured within one inspection setup.
What do the numbers mean?
Power & electrical5
Optics & imaging8
Control & software11
Configuration & options27
Vintage & configurations
Documented models & variants
| Designation | Generation | Vintage | Changes | Source |
|---|---|---|---|---|
| O-INSPECT 3 / 2 / 2 | — | 2022 | Stated with part number 636520-9932-000, electrical ratings of 50-60 Hz, max. 600 VA, 100-240 V, and vintage 2022. | Equipment inventory listing[2] |
What does it need to run?
Site utility requirements, footprint, and infrastructure needed to install and operate this tool. Sourced from public records.
Where are the manuals?
Generated from public-source data on file. Enter your email to access — nothing is published; details are routed privately.
Not publicly documented
Field notes
No research found yet — worked with this tool? Share what you know.
Frequently asked questions
What type of equipment is the Zeiss O Inspect 322?
The Zeiss O Inspect 322 is a coordinate measuring machine.[3][4][1]
What measuring volume is given for the Zeiss O Inspect 322?
The Zeiss O Inspect 322 has a measuring volume of X equals 300 mm, Y equals 200 mm, and Z equals 200 mm.[1]
What measurement technology is specified for the Zeiss O Inspect 322?
The Zeiss O Inspect 322 is specified with multisensor measurement technology using optical and tactile passive measurement.[1]
Not publicly documented
The following facts about the O Inspect 322 CMM are absent from this record as of this revision. First-hand knowledge or a citation closes a gap; every submission is reviewed before publication.
No publicly documented production dates or lifecycle milestones (introduction, end of production, EOL) for the O Inspect 322 CMM are on record.
Answerable by: OEM historical records or a trade-press announcement
The control-system platform and OS era of the O Inspect 322 CMM are not on record.
Answerable by: an engineer who operated it or OEM installation records
No publicly documented failure modes or field errata for the O Inspect 322 CMM are on record.
Answerable by: a field service engineer, process engineer, or maintenance technician
The process node or technology generation of the O Inspect 322 CMM is not on record.
Answerable by: an OEM datasheet or a fab qualification report
No publicly documented compatible parts, consumables, or accessories for the O Inspect 322 CMM are on record.
Answerable by: an OEM parts catalog or a service engineer
No research found yet — worked with this tool? Share what you know.
Sources & citations
Sources (4)Every fact above is drawn from these public sources
- [1]Inventory photo
- [2]Inventory photo
- [3]Equipment inventory listing
- [4]Equipment inventory listing
Last updated Oct 16, 2026.
Compare with similar tools
View all →The KLA .204 PSL Wafer is an 8-inch NIST-traceable reference wafer compatible with Surfscan 6xy0 and Sp1 particle counters.
KLA .496 PSL Wafer is an 8-inch NIST traceable wafer stated to be capable on Surfscan 6xy0 and SP1.
The KLA .498 PSL Wafer is a NIST traceable reference wafer.
